From: Larry Visoski

From: Larry Visoski To: [email protected] Subject: LSJ line array speakers Date: Sat, 06 Jul 2013 13:14:22 +0000 Jeffrey, My research found this line of outdoor, water/resistant speakers. These are Line Array outdoor deign, however its recommended the speakers should be protected from elements, Guitar Center carries this line, i will obtain pricing if you think this is speaker system you are thinking? Web link. httn://www.qscaudio.com/products/speakers/widelinewideline wx.htin Do you like this deign ? Thx, Larry Products / Loudspeakers / Line Array Systems WLWX Weatherized WideLine Systems WideLine-wx models are constructed using premium birch plywood which is full encapsulated in fiberglass. The input connector plate is replaced by a hardwired, captive, UV resistant, outdoor-rated (direct burial) cable with a gland-nut through the cabinet for waterproofing. The cable will be 3 meters in length unless otherwise specified at the time the order is placed. Grilles are stainless steel covered in outdoor rated, vinyl coating and lined with acoustic foam and a fine woven stainless steel mesh. WideLine WX models are strictly built to order. Please allow 90 days plus shipping time from the time the P.O. is delivered to QSC for delivery. WL2102-wx The WL2 I 02-wx is a weather resistant, installation version of the WideLine-I0 WL2102-w line array. All rigging hardware is removed and replaced with four female MI0 fittings (eight total) mounted to either end of the enclosure. The loudspeaker is designed for 3-way operation only and no handles are provided. An adjustable, external, bolt-on rigging system for box-to-box connection and adjustment of splay angles is included. The AF2102-wx is a compatible, aluminum array frame for use when suspending the WL2102-wx. Array frames for the standard WL2102-w are not compatible with the WL2102-wx. WL3082-wx The WL3082-wx is a weather resistant, installation version of the WideLine-8 WL3082 line array. All rigging hardware is removed and replaced with four female MI0 fittings (eight total) mounted to either end of WL2102-wx WL3082-wx GP218-wx LINE ARRAY SYSTEMS ILA Installation Line Array WideLine-1Q WideLine-8 Weatherized WideLine Systems DOCUMENTS User Manual (FIE=25212)_ RELATED PRODUCTS WiddinrainincAnay_Systrim Widdinataincitaay_Systcm siF)18-sw Subwoofez WL2l8-sw WideLine Subwoofer SC28 System Controller PSControl net BASIS IMPORTANT NOTE: Si; nal Processing Requirements Like most line-array systems available today, QSC WideLine and ILA line-arrays require carefully optimized signal processing in order to perform as intended. QSC has developed processing settings for these loudspeaker systems using our SC28, BASIS and Q-Sys digital processing devices. Arriving at these settings requires skilled engineers, sophisticated measurement equipment and repeated listening in various EFTA00695796 the enclosure. The loudspeaker is designed for 3-way operation only. An adjustable, external, bolt-on rigging system for box-to-box connection and adjustment of splay angles is included. The AF3082- wx is a compatible, aluminum array frame for use when suspending the WL3082-wx. Array frames for the standard WL3802 are not compatible with the WL3082-wx. GP218-wx The GP218-wx is a weather resistant, installation version of the WideLine-10 GP2I8 subwoofer. The standard version includes no suspension provisions but M 10 suspension points may be added on request. Weatherized WideLine SPECIFICATIONS WL2102-wx System Type Tri-amp line array element Transducers High-frequency Low-frequency Frequency Response (+.3 dB) Frequency Range (-10 dB) Continuous Power Capacity' Peak Output 2 Nominal Coverage Input Connectors Suspension / Attachment Points Weight (Net) Dimensions (HWD) 3" titanium diaphragm, neodymium magnet 2 x 10" transducer, 3" voice coil, ferrite magnet 55 Hz- 18 kHz 48 Hz - 20 kHz HF: 80 W LF/MF: 600 W HF: 127 dB LF: 133 dB H: 140° V: dependent on number of elements used Tinned, bare wire Integral rigging system, vertical splay adjustable in I° increments from 0*-10° 92.5 lb (42 kg) 11.75" x 27.25" x 18.5" 298 mm x 692 mm x 470 mm WL3082-wx GP218-wx Tri-amp line array element 3" titanium diaphragm, neodymium magnet Dual, 8" woofer, 2.5" voice coil 68 Hz- 18 kHz 62 Hz - 20 kHz HF: 85 W LF/MF: 250 W HF: 122 dB LF: 128 dB H: 140° V: dependent on number of elements used Tinned, bare wire Integral rigging system, vertical splay adjustable in 1° increments from 0°-10° 61 lb (27.7 kg) 9.5" x 20" x 15.5" 241 mm x 508 mm x 394 mm 2 x 18" vented subwoofer 2 x 18" transducers, 4" voice coil, ceramic magnet 31.4 Hz - 240 Hz (without processing) 27.4 Hz - 1.2 kHz (without processing) LF: 1700 W LF: 140.7 dB Tinned, bare wire None (M I0 points available by request) 215 lb (97.5 kg) 21.13" x 30.13" x 47.32" 537 mm x 765 mm x 1202 mm 2 Continuous !EC specified test signal, 2 hours bi-amp mode unless otherwise stated. 2 Calculated at I m using power capacity and system sensitivity 6 dB peak-to-average signal ratio assumed. Specifications subject to change without notice. Sent from my iPad environments. It is not possible to simply take the parameters from a QSC processor, transfer them to another processor and get the same results. Other processor manufacturers use different algorithms and design techniques that will produce a different transfer function even if the settings are substantially the same. As a result, QSC is unable to provide settings or tuning support for our line array systems when used with any processors other than those specified by QSC. EFTA00695797